Aviation Low-intensity obstruction lights
ZOM-80LED-VP™ >32cd, ICAO type «B»
The low intensity
obstruction light ZOM-80LED-VP is an aviation light-signal device that was
launched onto the market in 2010 and its performance was greatly appreciated by
a great number of our clients worldwide. The stationary LED module is a light
source, which consists of 80 red LEDs, 5-mm diameter, 12,5 cd each.
combines the innovative trends in the aviation light-signal equipment
production and modern vandal-proof obstruction
light body. Quality control at all production and supply stages enables to
prevent any claims.
lights filter is equipped with the outer Fresnel lens. Quality control at all
production and supply stages enables to prevent any claims.
lights ZOM-80LED-VP are produced according to 27.40.39-004-28320930-2018 specifications, and they
are used in the sets for multilevel high objects and constructions light
marking. Besides, they are intended for securing air travel safety by emitting
a light signal and warning pilots of approaching to high objects
(obstructions). This low
intensity obstruction lights red steady performance, type B, fully complies
with ICAO classification, which are required for the low intensity obstruction
lights mounted on stationary objects.
Benefits of our solutions:
· Broad supply voltage band allows connecting our obstruction lights to alternating and direct current
without observation of polarities.
· Built-in status monitoring system allows working capacity remote control (full obstruction lights
complex as well as each obstruction light separately).
· Status monitoring system contains galvanically isolated, normally-closed contacts allowing seamless
integration into any remote monitoring system.
· Based on LED-technology;
· Extremely reliable – long lifetime;
· Very low power consumption;
· 30-265V AC/DC nominal operating voltage;
· Stabilized light output;
· Easy to install, several mounting sets available;
· Long maintenance intervals;
· Supply power voltage variations do not affect to light output;
· Very low total lifetime costs;
· Lightweight and small – low wind load factor;
· No RF-radiations;
· Two (2) years warranty;
Main standards and requirements compliance:
· Order of Federal Air Transport Agency, Rosaviatsiya order, ¹262, dated of August 25, 2015;
· State Aviation Administration of Ukraine;
· ICAO Annex 14, 4th Edition, July 2004;
· ICAO low intensity type B;
· TR CU 004/2001 (Technical Regulation of Customs Union);
· TR CU 020/2011 (Technical Regulation of Customs Union);
· GOST R MEK 60598-1-2011 (All-Union State Standard);
· GOST 30804.3.2-2013 (All-Union State Standard);
· GOST IEC 61547-2013 (All-Union State Standard);
· STB IN 55015-2006 (Standards of Belarus).
· Climatic class: UHL1, GOST 15150 (All-Union State Standard);
· Operation conditions, GOST 17516.1 (All-Union State Standard);
· Protection class: IP65, GOST 14254 (All-Union State Standard);
· The obstruction lights ZOM-48LED-VP are resistant to frost, rain, salt spray, dust, vibration strain,
solar radiation, heat waves;
· The light filter: transparent, red of shockproof optical polycarbonate with UV-stabilizer DOW®
· Body material: shockproof polycarbonate with UV-stabilizer Bayer Makrolon® (Germany);
· Weight: no more 1,0 kg.
· Input power voltage, U(in): 50-265V AC. 30-350V DC;
· Input current AC/DC, I(in). (mÀ): 45…200;
· Maximum power consumption, no more (W): 6;
· Maximum switching contact voltage Contr, (V): 400;
· Maximum switching contact current Contr, (mA): 100.
· The light source - a semiconductor LED device;
· LEDs number: 80. Light intensity - 12,50 cd. Angle - 30°:
· Failure-free operation: 8000 hours;
· Emission: circular, red color;
· Light dispersion angle: rated 16 º, actual 17 º;
· Directed light intensity +6°: 39cd;
· Directed light intensity +10°: 33cd;
· Directed light intensity -6°: 34cd.
· A wide range of power voltage enables to switch the obstruction lights ZOM-80LED-VP with both AC
and DC power sources irrespective of polarities.
· The inbuilt monitoring status system enables to control performance of not only the whole
obstruction lights set, but also each separate light remotely.
· The monitoring status system contains galvanically isolated normally-closed contacts, which allows
getting it integrated into any remote monitoring structure.
None of LED light source used in obstruction lights,
which is available on the market, does not have the complete list of advantages
implemented in the obstruction lights of ZOM line.
1. The obstruction light (a body of light equipment) 1 item
2. Stationary LED module 1 item
3. Manual 1 item
Main mounting and operation requirements:
lights are mounted by a holder (a base stand) with outer G ¾” thread. The
mounting base stands are installed on top of high objects (roofs, etc.),
subject to light obstruction.
A stationary LED
module is a light source in the obstructions lights ZOM-80LED-VP, which does
not require any service and replacement for the entire period of its operation.
So as to connect
power and monitoring cables, you should unscrew the top part of the obstruction
light (the light filter) from its base and then get them connected. While
assembling the obstruction light, make sure that the rubber seal is tightly
seated. You should brush the light filter with clean cotton, soft flannel or
suede leather without using any solvent or grinding materials, if it gets
dirty. Finally, you should clean it with spirits-soaked cotton.
The obstruction lights
packaging according to GOST 23216 (All-Union State
Standard) for storage conditions 2 (s)
GOST 15150 (All-Union State Standard). The lights ZOM-48LED are packed in a shipping container, which secures
safety and protection from any mechanical damage and atmospheric precipitation.
Labor safety rules:
To provide safety operating the obstruction light, it is prohibited:
· To replace the stationary LED module of the obstruction light ZOM-80LED-VP for the light source with
lower light intensity value;
· To carry out any operations with the obstruction lights with power on;
· To assemble or operate the obstruction light with damaged insulation;
· To assemble and operate the obstruction lights, it is required to follow PUE (Electrical Equipment
Data about claims:
The claims are made to the supplier in case any
defects and malfunctions can be found which lead to the obstruction lights ZOM-80LED-VP
breakdown before warranty period expires.
You should state in the claim report:
The obstruction light type, defects and malfunctions,
conditions under which they were found, the operation time of the device. The
copy of the payment document for the device must be attached to the report.
The company guarantees 2-year
non-failure device operation, if all operation rules are observed.
Payment and Delivery:
We perform shipping to any region on Incoterms-2010 conditions.
Terms and delivery conditions are discussed individually.
Settlements are made by means of a bank transfer with an advanced contract on delivery.
For purchase, please contact: firstname.lastname@example.org